Download a PDF version of this article.
Failures on developments that incorporate timber windows are increasing. These failures range from failing joint integrity, drafts and water ingress resulting in damage to internal surfaces.
This article forms one of a series of articles that aim to highlight those common issues and the practices that should be advocated to mitigate their occurrence.
A major cause of failure for timber windows is water ingress around glazing. Water enters into the space between the glazing and the frame via defects during periods of rainfall and can also happen during cleaning e.g. jet washing. This water often becomes trapped and sits in concealed areas for prolonged periods until it builds to a level at which it enters frame joints emerging on the inside as water ingress.
A full set of design drawings and specifications shall be made available to the warranty provider and all other interested parties prior to the production of any windows, doors or door sets.
The following should be available:
It should be noted that where supporting test evidence or certifications/accreditations are not available e.g. bespoke window designs produced by small joinery workshops, a full specification for the windows shall be made available for review before production commences.
On-site testing at completion of the installation will be required. For guidance on site testing for water penetration’ reference should be made to CWCT test methods e.g. Technical Note No. 41 for guidance on site hose testing methodology.
An IGU, often referred to as a ‘double glazed unit’, is a combination of two panes of glass spaced apart with a spacer bar and sealed to form a single airtight unit with an air space in between.
The difference between double and triple glazing is as the names suggest. Triple glazing has an additional pane of glass, thereby creating air two spaces instead of one. The extra glass pane and gap increase the window's heat and sound insulation properties compared to double glazing.
IGUs have often included low energy coatings to the inner pane and gas fill (such as argon) in the space in between panes of glazing that make up the unit.
The use of IGUs referred to as ‘double glazing’ has been common within timber windows for a number of years. In the coming years, it is likely that an increase in the use of triple glazed units will become common practice to meet growing fabric energy standards.
‘BS 8000-7 Workmanship on building sites — Code of practice for glazing’ covers various methods that are applicable to the installation of IGUs. Of these however, within timber framed windows, we are likely to encounter the following approaches to glazing in most instances.
IGUs are installed on setting blocks and secured using proprietary self-adhesive glazing tape. The external glazing beads can be timber or even aluminium, but all incorporate a gasket which exerts pressure on the IGU face to create a weatherproof seal when fixed into position.
The lowest horizontal bead is set down on proprietary bead clip which holds the bottom bead higher than the surface of the glazing rebate to create a slot which allow drainage of water from the rebate. Note: Often the bottom bead is referred to as a ‘hook’ bead, as they ‘hook’ or locate into the clip system they are installed upon, often referred to as a ‘hook bead clips’.
IGUs are installed on setting blocks and secured using proprietary self-adhesive glazing tape. The timber external glazing beads incorporate a tape which exerts pressure on the IGU face when fixed into position.
The joint between the face of the glazing and the glazing bead then receives a capping of a one or two part curing sealant. The lowest horizontal bead must allow drainage of water from the rebate.
One or more of the following are often present in failing installations. Each can contribute in allowing water to enter the glazing rebate and become trapped in the area under the glazing. This eventually causes IGUs to fail, or allows water to enter concealed parts e.g. the joints, eventually finding a passage to the inside face of the window. In winter, any trapped water can freeze contributing to the IGU’s seals failure and it is not until the spring where misting in the IGU’s occurs, can the issue be seen.
No allowance for drainage
The IGU has been set too close or touching the rebates of the frame and inhibits the drainage of water. A 5mm drainage path between the edge of the IGU and the rebate should be provided all round the IGU perimeter as this space allows any water that does penetrate seals to run to the bottom of the glazed area where it can drain out.
No setting blocks under the IGU
IGUs should be set into position using location and setting blocks. These blocks should be placed at intervals around the perimeter of the IGU. The spaces in between allow for any penetrating moisture to run to the bottom rebate and drain out.
The upper surface area of the cill rebate should be angled at a 1:10 (approximately 5.5° angle) so that any water driven into concealed spaces is directed out to the external face via a continuous drainage slot.
Failing glazing beads
Mitred beading often leads to joints opening in service giving a direct path to moisture at corners. At the junction of bottom bead and vertical beads, water penetrating this area either becomes trapped or is directed into concealed areas of the frame.
To ensure robust and sustained weatherproof details, glazing beads should not be mitred at joints but cut squarely. The top horizontal glazing bead should run the full width of the opening to protect the top of the jamb beads on either side and the wider bottom bead should also run the full width of the opening and project to conceal the drainage weep slot provisions below.
The side (jamb) beads should be cut to stop short of the bottom bead by 3mm – where the bottom bead has a 1:6 (11° angle) weathering slope on its top surface, the gap can be reduced at the glass face by cutting the ends of the side beads to a shallower pitch.
The glazing beads should be securely fixed with non-ferrous pins or screws at a 200mm maximum spacing, starting at 50mm from corners to create a compression seal between the bead and the glass surface.
Incorrect use of sealant
The designed system of glazing has not been followed, and sealant has been used where it was not intended. Various systems can be used to seal contact points between glazed unit faces and beads e.g. self-adhesive dry glazing tapes, extruded gaskets, butyl tapes/gaskets with sealant capping. Importantly however mixing and matching approaches should be avoided and the ventilated and drained system must follow that proposed within designs.
On site operations that incorporate site applied capping sealant on drained and vented glazing systems should be executed in strict accordance with the design and specification.
Incorrect specification of sealant
In instances where butyl tapes/gaskets with sealant capping has been used, the use of an incorrect sealant specification can be the cause of many failures. Any voids that are created by shrinkage or lack of adhesion of the sealant will allow water through or become trapped resulting in water ingress or failure of the IGU.
For the purpose of warranty:
Timber windows should be preferably supplied to site fully finished and fully glazed to minimise the opportunity for moisture ingress to affect any part of the window during the build stage.
Read more articles on the Resource Hub and sign up to receive our blog round-up.
Every care was taken to ensure the information in this article was correct at the time of publication (September 2022). Guidance provided does not replace the reader’s professional judgement and any construction project should comply with the relevant Building Regulations or applicable technical standards. For the most up to date Premier Guarantee technical guidance please refer to your Risk Management Surveyor and the latest version of the Premier Guarantee Technical Manual.